These are the terms used across the six guides, grouped in the order the guides introduce them. Each definition is a short version of the explanation in the guide named under each group, and each guide lists the documents it is based on. Where a term has more than one common name, both are given.
Inside a cylinder
Explained in How a pin tumbler lock works.
- Cylinder
- The self-contained lock unit with the keyhole in its face, made of a fixed housing and a plug that turns inside it.
- Housing (shell)
- The fixed outer part of a cylinder. It holds the upper part of each pin chamber and the springs.
- Plug
- The inner part of a cylinder that rotates when the right key is turned. The key goes into the plug, and a cam on the back of the plug moves the bolt or latch.
- Cam
- The arm or wing on the back of the plug that turns with it and moves the bolt. Yale's 1865 patent calls it a wing.
- Pin stack
- The set of parts in one chamber of a pin tumbler lock: a key pin, a driver pin and a spring.
- Key pin
- The lower pin in a stack, which the key touches. Key pins come in different lengths, and those lengths decide which key fits the lock.
- Driver pin
- The upper pin in a stack, pushed down by the spring. With no key in the lock, driver pins reach across into the plug and stop it turning.
- Spring
- The small coil spring above each driver pin that pushes the stack down towards the keyway.
- Shear line
- The boundary between the outside of the plug and the inside of the housing. The plug can turn only when the split in every pin stack sits on this line. It gives this site its name.
- Tumbler
- A general name for any movable part that a key has to set before a lock opens: pins, wafers, discs and levers are all tumblers.
Other mechanisms
Explained in Wafer, disc and lever locks compared.
- Wafer
- A flat plate that slides across the plug, with an opening the key passes through. A wafer lock opens when every wafer is centered within the plug and none reaches into the housing.
- Sidebar
- An extra locking part along the side of a plug that has to be moved out of the way by the correctly set tumblers before the plug can turn.
- Disc lock (disc detainer lock)
- A lock in which the key rotates a stack of notched discs instead of lifting pins.
- Locking bar
- In a disc lock, the bar that keeps the inner cylinder from turning until the notches of every disc line up to form a channel it can move into.
- Lever tumbler
- A flat, pivoted plate in a lever lock. The key lifts each lever to a set height.
- Gate (gating)
- The slot cut through a lever. The bolt can move only when the gates in all the levers line up.
- Stump
- The small post on the bolt of a lever lock that has to pass through the gates of the levers.
Keys and keyways
Explained in Keys, key blanks and keyways.
- Bow
- The part of a key you hold.
- Blade
- The part of a key that goes into the lock.
- Bitting (cuts)
- The cuts along the edge of a key blade that set each pin or wafer. This site explains what bitting does, not how it is measured or cut.
- Key blank
- A key with the right bow and blade profile but no cuts yet. The same blank can become many different keys.
- Keyway
- The slot in the face of a plug. Its outline decides which blanks can be inserted.
- Ward
- A ridge or step in a keyway that a key blank has to clear, matched by a groove milled along the blank.
- Master key
- A key that opens several locks in one system, each of which also has its own key. Losing one affects every lock it opens.
- Restricted keyway
- A keyway whose matching blanks are distributed in a controlled way, so that copies are harder to make.
- Key control
- Knowing who holds which keys and being able to limit copies.
Doors and ratings
Explained in Choosing locks for a home.
- ANSI/BHMA
- The American National Standards Institute and the Builders Hardware Manufacturers Association. BHMA develops the ANSI-accredited A156 series of performance standards for door hardware.
- Grade 1, 2 and 3
- The product grades defined in many ANSI/BHMA standards, with grade 1 the highest.
- Residential rating (A, B, C)
- The ratings under the residential standards A156.39 (locksets and latches) and A156.40 (deadbolts): a separate letter for security, durability and finish, where C is good, B better and A best.
- Lockset
- The knob or lever hardware on a door, with its latch and, where fitted, its lock.
- Latch
- The bolt in a knob or lever set that holds a closed door shut.
- Deadbolt
- A separate bolt thrown into the frame by a key or thumb turn, in addition to the latch.
- Single cylinder deadbolt
- A deadbolt with a key outside and a thumb turn inside.
- Double cylinder deadbolt
- A deadbolt that needs a key on both sides. Police advice notes the fire safety concern and that some building codes restrict them.
- Throw
- The length of bolt that goes into the frame when a deadbolt is locked.
- Strike plate
- The metal plate on the door frame that receives the bolt or latch, and the usual weak point when a door is forced.
- Backset
- The distance from the edge of a door to the center of the hole for the lock.
- Latch guard
- A plate that covers the gap where the latch and bolt meet the frame.
Cars
Explained in Car locks and transponder keys.
- Immobilizer
- An electronic device that controls the ignition, fuel system or starter and does not let the engine start without the correct signal.
- Transponder
- An electronic proximity device that sends a coded radio signal. A transponder key carries one so that the immobilizer can recognize it.
- Antitheft device (federal rules)
- In US federal vehicle theft rules, a standard device that, among other things, draws attention to attempts to enter or move a vehicle by means other than a key and prevents the vehicle running after unauthorized entry.
After a loss
Explained in What to do after losing your keys.
- Rekeying
- Changing a lock so that it works with a new key and no longer with the old one, by replacing the parts that decide which key fits, such as the key pins, while keeping the rest of the lock.
- Itemized invoice
- A bill that lists parts, labor, mileage and the service call separately, which consumer agencies advise asking for after any locksmith visit.
Back to all guides